.. index:: ! psrose .. include:: module_core_purpose.rst_ ****** psrose ****** |psrose_purpose| Synopsis -------- .. include:: common_SYN_OPTs.rst_ **gmt psrose** [ *table* ] [ |-A|\ *sector_width*\ [**+r**] ] [ |SYN_OPT-B| ] [ |-C|\ **m**\|\ [**+w**]\ *mode_file* ] [ |-D| ] [ |-F| ] [ |-G|\ *fill* ] [ |-I| ] [ |-J|\ **X**\ *diameter* ] [ |-K| ] [ |-L|\ [*wlabel*\ ,\ *elabel*\ ,\ *slabel*\ ,\ *nlabel*] ] [ |-M|\ *parameters* ] [ |-N|\ *mode*\ [**+p**\ *pen*] ] [ |-O| ] [ |-P| ] [ |-Q|\ *alpha* ] [ |-R|\ *r0*/*r1*/*az0*/*az1* ] [ |-S|\ [**+a**] ] [ |-T| ] [ |SYN_OPT-U| ] [ |SYN_OPT-V| ] [ |-W|\ [**v**]\ *pen* ] [ |SYN_OPT-X| ] [ |SYN_OPT-Y| ] [ |-Z|\ **u**\|\ *scale* ] [ |SYN_OPT-bi| ] [ |SYN_OPT-di| ] [ |SYN_OPT-e| ] [ |SYN_OPT-h| ] [ |SYN_OPT-i| ] [ |SYN_OPT-o| ] [ |SYN_OPT-p| ] [ |SYN_OPT-qi| ] [ |SYN_OPT-t| ] [ |SYN_OPT-:| ] [ |SYN_OPT--| ] .. include:: rose.rst :start-after: .. module_common_begins :end-before: .. module_common_ends .. include:: common_classic.rst_ Examples -------- .. include:: explain_example.rst_ To plot a half circle rose diagram of the data in the file fault_segments.az_r (containing pairs of (azimuth, length in meters), using a 10 degree bin sector width, on a circle of diameter = 6 inch, grid going out to radius = 150 km in steps of 25 km with a 30 degree sector interval, radial direction annotated every 50 km, using a light blue shading outlined by a solid red pen (width = 0.75 points), draw the mean azimuth, and shown in Portrait orientation, use: :: gmt psrose fault_segments.az_r -R0/150/-90/90 -Bx50g25+l"Fault length" -Byg30 -B+t"Rose diagram" -JX6i -A10+r -Glightblue -W0.75p,red -Z0.001 -Cm -P -T -: > half_rose.ps To plot a full circle wind rose diagram of the data in the file lines.r_az, on a circle of diameter = 10 cm, grid going out to radius = 500 units in steps of 100 with a 45 degree sector interval, using a solid pen (width = 0.5 point), and shown in landscape [Default] orientation with UNIX timestamp and command line plotted, use: :: gmt psrose lines.az_r -R0/500/0/360 -JX10c -Bxg100 -Byg45 -B+t"Windrose diagram" -W0.5p -U+c | lpr Redo the same plot but this time add orange vector heads to each direction (with nominal head size 0.5 cm but this will be reduced linearly for lengths less than 1 cm) and save the plot, use: :: gmt psrose lines.az_r -R0/500/0/360 -JX10c -Bxg100 -Byg45 -B+t"Windrose diagram" -M0.5c+e+gorange+n1c -W0.5p -U+c > rose.ps .. include:: rose.rst :start-after: .. module_note_begins :end-before: .. module_note_ends See Also -------- :doc:`gmt`, :doc:`gmt.conf`, :doc:`gmtcolors`, :doc:`pshistogram`